Welcome to our store - Tel: 0207-965-7502. Contact Us

EXPERT ADVICE • FINANCE OPTIONS • INSTALLATION SUPPORT

Gas Supply for a Combi Oven: What a UK Kitchen Needs

Gas combi oven with visible supply pipework

Simon Durham |

A gas combi oven needs four things from your site: the right gas type (natural gas or propane), the right supply pressure, enough pipework capacity for the burner, and proper ventilation and flue arrangements. Get those four confirmed before you order, and the oven goes in once and runs for years. Get one wrong and you face delays, a failed commissioning or a kitchen that can’t cook at peak. We sell and advise on combi ovens for UK bakeries, cafes, restaurants and caterers, and this guide covers the questions we would want answered before any gas oven is specified.

Thecommercialovenstore
Choose the Right Combi Oven
The Commercial Oven Store offers expert advice on choosing commercial ovens for your kitchen’s needs, including options from Rational and Unox.
Visit

TL;DR

  • A gas combi oven heats with a gas-fired burner and makes steam, so it works across the same 30 to 300°C range as an electric one.
  • Match the oven to your gas: a natural gas appliance must never be connected to propane or butane without correct conversion, because carbon monoxide can result.
  • Check supply pressure, meter and pipe capacity, an accessible isolation valve, ventilation and the flue type before you order.
  • Installation to the catering standard and an annual safety check are part of owning a gas appliance, so budget for them.
  • If your site’s gas is not ready, talk to us before you buy: our Expert Advice team helps you match the oven to the kitchen.

Table of Contents

What a gas combi oven does with its gas

A combination steam oven cooks with hot air and saturated steam, separately or together. According to the UK government’s Energy Technology List, these ovens run on either electricity or gas. The heat comes from an electric element or a gas-fired burner, and the oven works from 30 to 130°C in steam mode and 30 to 300°C in convection and combination modes.

For the cook, the result is the same: roasting, baking, steaming, regenerating and holding all from one cabinet. For the person planning the kitchen, the difference is what sits behind the oven. An electric oven asks questions about the electrical supply (we cover those in our guide to commercial oven power requirements). A gas oven asks about gas, air and fumes.

That last point matters because burning gas produces combustion products that must leave the building. A gas combi therefore needs a route for its exhaust, and a supply of fresh air to burn the gas safely. Everything in the rest of this article follows from those two facts.

Natural gas or propane: choose before you order

Most city-centre units run on mains natural gas. Rural sites, mobile units, pop-ups and some food halls often rely on bottled or tanked LPG (liquefied petroleum gas, such as propane). The same oven model is usually offered in versions for each gas, and they are not interchangeable by plugging in a different hose.

An Irish gas-industry technical bulletin explains why. Propane and butane have a higher calorific value than natural gas and need more than twice the amount of air for complete combustion. If an appliance made for natural gas is connected to an LPG supply, carbon monoxide will be produced. The same bulletin says the person commissioning the appliance is always responsible for checking that it is set up for the correct gas type and operating pressure before it goes into service.

In practice that gives you three rules:

  1. Confirm your gas type first. Know whether your premises are on mains natural gas or LPG before you look at models.
  2. Order the matching variant. The model code or data plate states the gas category the oven was built for.
  3. Have the commissioning engineer check type and pressure on the day. Never assume a delivered oven is set for your supply.

If you want a second pair of eyes on the specification, our Expert Advice service exists for exactly this: tell us your premises, your gas and your menu, and we will help you match the oven to them.

Supply pressure, pipework and the isolation valve

The oven’s burner is designed for a particular pressure at the appliance. One manufacturer’s installation manual for a gas combi gives a supply pressure of 17.4 mbar for natural gas and 27.4 mbar for propane. Those figures belong to that model, and other makes state their own, so read the data plate and installation manual for the oven you are buying. The point is that pressure is a specified number, not a rough guide.

The same manual tells the installer to consult the local gas utility to check that the available supply is compatible with the appliance’s consumption, and to fit a rapid gas shut-off cock upstream of the appliance, in an easily accessible position.

Before you commit, gather this information:

Check Why it matters Who confirms it
Gas type on site Decides which oven variant you order You, from your supplier or tank contract
Appliance gas rate (kW) Compare against the gas the meter and pipes can deliver Oven data sheet
Meter and pipe capacity A new oven adds to the load of existing equipment such as ranges and fryers Gas engineer, with the gas utility where needed
Working pressure at the appliance Burner performance depends on it Gas engineer at commissioning
Isolation valve position Must be a quick, accessible shut-off Installer

The most common surprise is capacity. A kitchen that ran fine on a range and a fryer may not have pipework sized for a large combi on top. Ask a competent gas engineer to size the supply against everything that burns gas at the same time, not just the new oven. Gas published ratings for combi ovens vary widely by size, so a small 6-grid unit and a large 20-grid unit put very different demands on the pipe.

Our article on preventing common on-site failures in UK combi oven installations covers the practical side of site surveys, and our combi oven capacity guide helps you choose a size before you work out the supply.

Ventilation and flue: the part that stops installations

Gas needs air. Approved Document J, the 2022 building regulations guidance for England on combustion appliances, states that appliances need ventilation to supply air for combustion, that vent sizes depend on the fuel burned, and that provision usually has to increase when a room contains more than one appliance. That last part describes most professional kitchens.

Then there is the exhaust. The installation manual we mentioned classifies its gas combi ovens by construction type (A3 or B13). Before the discharge system is installed, the installer must identify the type and follow the matching diagram: exhaust under an extraction hood, directly to the outside, or into a central flue. The same manual states that the need for a properly designed ventilation system cannot be over-emphasised, and that problems due to improper ventilation are not covered by the warranty.

So before ordering, decide which route your kitchen will use:

  • Under an existing extraction hood. Check the hood’s extraction rate covers the new appliance as well as existing equipment.
  • Direct to outside. Needs a suitable wall or roof route and a terminal in an approved position.
  • Into a central flue. Needs a compatible flue, designed and maintained to the relevant standard. For open-flue gas appliances, BS 5440-1:2023 sets out requirements for installing and maintaining the chimney. It applies to appliances up to 70 kW net input.

Ventilation rules for commercial kitchens are a topic of their own. Our guide to UK oven ventilation rules and compliance steps walks through the extraction rates, and if you plan to cook pizza or other high-heat products, read our note on checking ventilation before buying a combi oven for pizza.

Who installs it, and which standard applies

A gas combi is not a plug-in appliance. The connection, the flue and the commissioning should be done by a competent, Gas Safe registered engineer who works on commercial catering equipment. Approved Document J points to the British Standard for installing gas-fired catering appliances in all types of catering establishments. The edition it names, BS 6173:2001, has since been superseded by BS 6173:2020, so ask your engineer to work to the current edition.

After installation, the checks continue. Under the Gas Safety (Installation and Use) Regulations 1998, as amended, landlords must ensure each appliance and flue is checked for safety within 12 months of installation and at intervals of no more than 12 months after that, as the HSE’s L56 guidance explains. If you lease your premises, find out whether that duty sits with your landlord or with you under the lease. Even where it does not apply to you, an annual check is the sensible rhythm for a busy kitchen. The same HSE guidance notes that, since 6 April 2018, the check can be carried out in the two months before the due date while keeping the original expiry date, so you can book it without losing time.

Tightness testing of gas pipework is carried out by the engineer, and industry practice on how it is done has been updated recently. You do not need to learn the test method. Do ask your engineer to confirm the pipework has been tested and to give you the paperwork, and keep it with your equipment file for your insurer and your environmental health officer.

Our commercial oven maintenance schedule shows how to fit the annual gas safety visit alongside descaling and routine cleaning.

Who installs it, and which standard applies

Running costs: what gas actually buys you

Gas is often chosen because kitchens expect lower running costs. The Energy Technology List sets a maximum energy consumption for a loaded oven in convection mode of 0.26 kWh per stone for electricity and 0.27 kWh per stone for gas (a stone being the standard test load). The two figures are close, so the real saving or cost depends on your unit prices for each fuel, which change with your contract, and on how hard you work the oven.

What moves your bill most is workload, not fuel type:

  • Batch size. A full oven cooks more per kWh than a half-empty one.
  • Preheating. Switching on an hour before service burns energy for nothing.
  • Mode. Steam, combination and convection use energy differently.
  • Door opening. Every opening loses heat and steam.

For worked numbers, see our article turning ETL test data into daily combi oven energy costs for UK kitchens, and our guide to using eco mode on combi ovens. Check your own gas unit rate on your latest bill before you work out a payback. Use your bill rather than a published average, because rates vary by supplier and change often.

A step-by-step plan before you order

Here is the order we suggest for a kitchen planning a gas combi.

  1. List what already burns gas. Ranges, fryers, grills and boilers all draw from the same supply and share the same room air.
  2. Confirm your gas type. Mains natural gas or LPG decides the variant. Where it goes wrong: ordering the common variant without checking.
  3. Choose the size from your menu, not the budget. Covers per service and trays per batch set the grid count. A bigger gas rate means more demand on pipes and flue.
  4. Ask a gas engineer to survey. They check meter and pipe capacity, pressure, the isolation valve position and the route for the exhaust. Where it goes wrong: finding out on installation day that the pipe is undersized.
  5. Settle ventilation and flue. Hood, direct to outside or central flue, and whether the air supply is enough for all the appliances. This is the step that most often causes delay.
  6. Plan the stand and the space. Allow clearances, a stable stand and room for service access. Our guide to enclosed oven stands to BS EN 127 helps with the specification.
  7. Book installation and commissioning. The engineer sets the gas type and pressure, checks the flue and gives you the paperwork.
  8. Diarise the annual safety check. Put it in the calendar when the oven goes live.

If you would rather not carry the planning yourself, that is the point of talking to us first. Our Expert Advice helps you match the oven to the kitchen, and we offer an Installation Service as part of buying from us.

Where we come in

We supply commercial combi, convection and speed ovens from makers such as Rational, Unox and Merrychef, with accessories like stands, grids and trays, and flexible payment and leasing options for businesses. If you are comparing a gas oven with an electric one for a site where the gas supply is uncertain, tell us about the kitchen. The Expert Advice team will help you weigh the supply, the space and your menu, so you order the right oven the first time. Our range includes electric combi ovens, such as the Rational iCombi Pro 10-1/1 and the Rational iCombi Pro 20-1/1, which put the planning questions on the electrical side instead.

Thecommercialovenstore

Browse the commercial ovens collection, or contact us through our store for advice on your kitchen.

Our view on gas supply

A gas combi oven is only as good as the supply behind it. We have seen the pattern often enough in how kitchens plan: the oven is chosen first, and the gas, the air and the flue are looked at afterwards.

Our advice is to reverse that. Start with what your site can deliver, then choose the oven that fits it. A well-matched oven cooks faster, holds steady through a Saturday rush and does not leave you waiting for a second visit from the engineer.

That is why we pair the range with Expert Advice and an Installation Service. Whether you end up with gas or electric, the aim is the same: the right oven, installed properly, from a supplier you can ask questions of.

Simon

FAQ

Can I run a natural gas combi oven on propane?

Not without the manufacturer’s conversion and a competent engineer to carry it out. Propane burns at a different pressure and needs more air, and connecting a natural gas appliance to LPG will produce carbon monoxide. Order the variant built for your gas, and have the engineer check type and pressure at commissioning.

What gas pressure does a combi oven need?

It depends on the model and the gas. One manufacturer’s manual specifies 17.4 mbar for natural gas and 27.4 mbar for propane. Read the data plate and installation manual for the oven you buy, and have your engineer measure the working pressure at the appliance.

Does a gas combi oven need a flue or extraction hood?

Yes, the combustion products must be removed. Depending on the oven’s construction type, that means exhausting under an extraction hood, directly to the outside or into a central flue. Ventilation also has to supply enough air for combustion, so plan both before you order.

How often should a gas combi oven be safety checked?

The HSE’s guidance for landlords is a check within 12 months of installation and then at intervals of no more than 12 months. If you rent your premises, check who holds that duty under your lease. Either way, book an annual visit from a Gas Safe registered engineer.

Sources